Cheap Polarized Bicycling Sunglasses to Prevent Debris, Bugs, Wind

I’ve been riding my bike a lot for the new year because my current Oakley Flak Jacket XLJ were letting in a lot of bugs, debris and wind into my eyes. So I visited my local Walmart to check out the local, cheap sunglasses available.

I was pleasantly surprised to find a pair of Foster Grant wrap sunglasses that wrapped completely around my eyes without causing any distortion issues. They also prevented any wind, debris or bugs from getting through. I’m a big fan of bronze polarized lenses and these included both features. And at $14.97, you can’t go wrong.

Below are the details of the sunglasses.

Foster Grant $14.97

Reduces Glare

Comfortable and Lightweight

100% UVA-UVB Protection

TR90 Polarized Flexible Frame

Wal-Mart Link

Markings on the Legs:

  • 193033031179
  • SR0918 YMA 1802 GRN POL FWM

UPC Details:

  • LL10
  • 10246142.FWM
  • Barcode 193033031179

Honda Lacquer Touch-up Pen Paint Tool Instruction Manual & Download

So I purchased a Honda Lacquer Touch-up Paint Tool Pen from Amazon but the instructions were tiny and I could barely read them. So for those of you that can’t read 6pt text, below are the instructions for applying the Honda Lacquer Touch-up Paint Tool pen.

Click Here to Download the Honda Lacquer Touch-Up Paint Instructions as a PDF

ABRASIVE PREP TIP: Use pointed edge to remove loose paint and rust, or the flat face to smooth down edges and clean larger areas.

PAINT PEN: Shake 20-30 seconds to mix paint. Start paint flow by depressing pen tip in an up and down motion on a hard test surface until paint begins to flow. Increase paint flow by depressing pen tip, minimize flow by decreasing pressure.

TO OPEN: Hold container upright, and twist applicator grip counter clockwise for either the paint tip, brush, or top coat applicator. Keep upright when opening.

PAINT APPLICATION: One coat prime and paint formula. Wipe surface with a clean lint·free cloth using rubbing alcohoI to remove oil, wax or grease build·up. Allow 30 minutes dry time for additional paint or top coat.

PAINTBRUSH: Tapered brush for large chips and scratches.

TOPCOAT APPLICATOR: Foam brush for top seal coat.

Honda Lacquer Touch-Up Paint Instructions


How to Fix a Blank White Page During SavSoftQuiz Installation

When installing SavSoftQuiz, you might get a white, blank error page. That’s because the installation documents and instructions are missing a critical component to the installation.

To fix the blank, white page, do the following:

Go to /application/config/config.php and scroll down to around line 477 and look for:

$config[‘sess_save_path’] = ‘null’;

and change it to

$config[‘sess_save_path’] = ‘public_html/quiz/application/cache’;

Important Note: my installation is in so if your installation is in a different folder, change the red quiz folder above to the correct one you’re using. Or if it’s in the root, remove ‘quiz/’ completely.

Save the changes and the installation should go perfectly.

I really hope they fix their documentation page.

How to Eliminate & Permanently Get Rid of Cockroach Infestations

I just read an incredibly helpful post on Reddit about eliminating cockroach infestations. The original poster mentioned using gel bait and Combat to get rid of the roaches. But this commenter had a much better solution. Here it is for anyone having this problem… Continue reading “How to Eliminate & Permanently Get Rid of Cockroach Infestations”

Brother HL-2230 Laser Printer Creases & Creasing on Manual Duplex Printing

I have a Brother HL-2230 Laser Printer and I just started printing hundreds of duplex prints for a school project. In case you don’t know, duplex printing is when you’re trying to print on the front and back of one single page. Unfortunately, the pages in my Brother HL-2230 kept getting creases during the printing of the second side and it was ruining my print outs. Well, I finally figured out the solution for preventing the creases on the second side. Continue reading “Brother HL-2230 Laser Printer Creases & Creasing on Manual Duplex Printing”

Namecheap Advanced DNS Settings for Verifying a Subdomain with Mailgun SPF & DomainKeys

Are you running your DNS on Namecheap’s Advanced DNS Settings? Are you desperately trying to verify your Subdomain at Mailgun with no success? You’re not alone. I was recently able to verify my settings with the help of the this blog post. But I felt a screenshot was necessary to make it easier to understand. Continue reading “Namecheap Advanced DNS Settings for Verifying a Subdomain with Mailgun SPF & DomainKeys”

How to Disable TLS 1.0 on Sophos UTM for PCI Compliance

Trying to pass PCI Compliance with your Sophos UTM? Good luck. You can’t as of 12/15/2015. Maybe someday they’ll release an update that allows you to easily “check” a box. Until then, welcome to the Sophos Command Line!

Warning: I’m a Linux beginner. But these steps worked for me. By the way, Sophos said this voids the support warranty. When I pressed the issue, they stated it doesn’t void my support agreement. I still don’t understand what it voids so proceed with caution.

  1. In the Sophos Dashboard, go to Management > System Settings > Shell Access. Create a password for root and loginuser and click the “Set Specified Passwords” box. Then, make sure the network you’re connecting from is in Allowed Networks. Finally, make sure “Allow password authentication” is checked. Hit Apply and again, make sure the green “On/off” switch is ON at the top right corner.
  2. Go download and install Putty and WinSCP.
  3. Start with WinSCP. We’re going to make a backup, first.
    1. Enter the IP and Port (2222) and connect to your Sophos UTM.
    2. Go ‘up’ a few levels until you’re at the Root folder. Then, navigate towards the /var/chroot-httpd/etc/httpd directory.
    3. Download the httpd.conf file by dragging the file from the right side to the left side (like FTP).
    4. Great. We have a backup with the original text inside. Disconnect your session. I have no idea how to restore, btw. That’s how much I suck. But we have a backup!! 🙂
  4. Start Putty and connect to the same IP and port. We’re going to edit that same httpd.conf file in the command line.
    1. First, login with loginuser and press enter.
    2. Type su then press enter.
    3. Enter your root password and press enter.
    4. Type CD / and press enter. You’re at root now.
    5. Now type CD var/chroot-httpd/etc/httpd and press enter.
    6. To edit the file type vi httpd.conf and press enter.
    7. Use the down arrow key to scroll down near the bottom of the file. You’re looking for SSLProtocol +TLSv1 +TLSv1.1 +TLSv1.2
    8. Once you spot it, press the Insert key on your keyboard and use the keyboard to change the +TLSv1 to TLSv1
    9. Press ESC to exit the editing mode.
    10. Now press : (you might have to press enter after typing the colon). This should take you to the bottom of the screen.
    11. After the : type x and press enter. This should save the file and get you back to the command  line.
    12. At the command line, paste this entire code and hit enter to restart httpd:
      /etc/init.d/httpd restart
    13. Once it restarts, at the command line, you can verify TLS 1.0 is disabled by pasting this line and pressing enter:
      openssl s_client -connect localhost:4444 -tls1
    14. If properly disabled, it will say the handshake failed or something similar.
    15. Type quit and close Putty. You’re done.

Note: You’ll need to repeat these steps every time you update the Sophos UTM firmware. Thanks for nothing, Sophos. 😦

Huge thanks to Colorado State University for the VI commands above.